RF Signal Detector with Environment Adaption Lens Finder Expert 3G Detection 50-6Ghz
Descriptions:
This wireless signal detector device boots self-detecting voice broadcast but does not affect the state of radio, 8LED signal strength indicator, clear various signal status and battery status, three alarm modes BAV, automatic detection signal category, WIFI identification, battery and charging status, You can find a static bug, detect it in the standby state, and also have a LENS finder. With sensitivity adjustment and volume adjustment and volume adjustment knob. With professional 3G detection.
| No. | NAME | DESCRIPTION |
| 1 | Power | Switch on |
| 2 | Vibration | Vibration warning mode (manual shift) |
| 3 | Beep | Beep sound warning mode (Default) |
| 4 | Hi Signal | Warning of strong signal in around |
| 5 | CAM / Bug / LTE | Analog / Spread spectrum signal of Camera, bug and cellphone |
| 6 | WiFi | Digital signal of WiFi and IP camera |
| 7 | Battery low | Battery power running down |
| 8 | Charging | Status of battery charging |
| 9 | 5. Yellow LED + 6.Blue LED light up | Detected radio wave of 3G 2100 |
HOW TO OPERATE:
1. Pull out the antenna and turn on this device. This device will do power-on self-test and then run power-on environment adaption. After the power-on actions are completed, this device will remain the Power and Beep LED lit up. And then the Yellow and Blue LED will start blinking, indicate this device is in detecting.
2. If more than one strength indication 8-LED lights up and beeps go off (vibrate), it means that there is RF (wireless) device operating around. If Hi Signal LED lights up at the same time, the detected radio wave is very strong.
3. Refer to the chapter of “How to find (locate) the signal source” to find the position of signal source.
4. Press once both the 2 buttons in left side of front view, can change the warning mode cyclically, beep à vibrate à beep à vibrate ...
5. To detect without other’s awareness, set the warning mode at Vibration or connect with earphone for silent detection.
HOW TO FIND (LOCATE) THE SIGNAL SOURCE:
1. Set the warning mode at Beep or connect earphone to find (locate) the signal source. Vibration is not suitable for finding the signal source.
2. Correct holding way of this device is the front side (with LED and speaker) facing to user and keep the antenna in upward.
3. Hold this device to scan half around to detect the signal. Forward one footstep to the strongest signal direction. When the 8-LED signal strength indication all light up and the scan range (angle) over 120 degree, press once the – (minus) button to lower down one level of the sensitivity.
4. The 8-LED signal strength indication will reduce to 3 or 4 LEDs lighting up and the scan angle will become smaller. Hold this device to scan half around and forward one footstep to the strongest signal direction.
5. Repeat above step 3 and 4, should be able to approach and then get the signal source.
6. If lose the signal during locating the position of signal source. Press and hold the “Env. Adapt” button for 3 seconds, this device will run environment adaption once and will get the signal to continue the detection.
DISCOVER GSM / 3G / 4G BUG & SPY CAMERA :
This device can detect and locate new bug and new spy camera remote controlled by cellphone.
Detect GPS tracker (2G / 3G / 4G Multi networks modem):
- GPS tracker sends "location data" or voice communication of the traced target through GSM / 3G modem to enable the trace person knowing the activity of traced target. Advanced GPS tracker has 2G / 3G / 4G multi networks modem.
- 3G 2100 is difficult to detect since its output power is small. This device has expert 3G 2100 detecting ability up to 7 meters, 2G up to 15 meters and 4G up to 4 meters. This device has superior performance to detect all kinds of GPS tracker efficiently.
- Most GPS trackers have motion sensor to sense unusual movement. Keep rocking the car and will activate the GPS tracker to send signal which will help this device find and locate the unauthorized GPS tracker.
Package Contents:
| 1. | Environment adaption RF Bug Detector | 2. | Switching power adaptor x 1 |
| 3. | Earphone x 1 | 4. | Rechargeable batteries x 4 (optional) |
| 5. | USB-Mini USB cable x 1 | 6. | Lens Finder x 1 |
Product Tags:
|
|
RF Bug Camera Detector WIFI Identification With Environment Adaption Lens Images
|
